Accuracy of the geometric shape of the hole in the longitudinal section during honing

Cover Page

Cite item

Full Text

Abstract

The wide application of honing as a finishing treatment of internal cylindrical surfaces for cylinder-piston systems, used in some structures, is caused by high accuracy measured in tenths of a micrometer, and high productivity of the process. The most important indicator of reliable operation of cylinder-piston systems are high requirements for the geometric accuracy of holes. Due to the lack of sufficient theoretical justification for the selection of honing parameters ensuring the accuracy of the geometric shape of the hole in the longitudinal section, the authors proposed a model for the formation of errors in the geometric shape of the hole. The model is built on the kinematic characteristics of the process including the ratio of the honing stone dimensions, the length of the hole, the stroke of the honing head, the ratio of the speeds of translational and rotational movements, and the force action in the processing zone, which changed due to the presence of an overrun of the honing stone. To obtain analytical dependencies ensuring the minimisation of form deviations, the conditions for stock removal for the points of the machined surface were considered, the value of which was taken proportional to the path of movement, and the pressure value. For this purpose, graphs of the distribution functions of displacements and pressure changes were constructed depending on the coordinate of the point location on the generating line of the hole being machined. Using the obtained analytical dependencies, the potential occurrence of a shape error in the form of a saddle shape was found, the dominant factor influencing the value of which is the value of the honing stone overrun. At the same time, it was identified that the ratio of the speeds of translational and rotational movements has an insignificant effect on the violation of the form in the longitudinal section.

About the authors

Aleksandr F. Denisenko

Samara State Technical University

Author for correspondence.
Email: tmsi@samgtu.ru
ORCID iD: 0000-0001-6393-2831

Doctor of Sciences (Engineering), Professor, professor of Chair “Mechanical Engineering Technology, Machines and Tools”

Россия, 443100, Russia, Samara, Molodogvardeyskaya Street, 244

Roman G. Grishin

Samara State Technical University

Email: grg-s1@mail.ru
ORCID iD: 0000-0003-4511-9147

PhD (Engineering), Associate Professor, assistant professor of Chair “Mechanical Engineering Technology, Machines and Tools”

Россия, 443100, Russia, Samara, Molodogvardeyskaya Street, 244

Evgeniya D. Antipova

Samara State Technical University

Email: antipova.ev.smr@yandex.ru
ORCID iD: 0000-0002-1759-7080

postgraduate student of Chair “Mechanical Engineering Technology, Machines and Tools”

Россия, 443100, Russia, Samara, Molodogvardeyskaya Street, 244

References

  1. Sender P., Buj-Corral I. Influence of Honing Parameters on the Quality of the Machined Parts and Innovations in Honing Processes. Metals, 2023, vol. 13, no. 1, article number 140. doi: 10.3390/met13010140.
  2. Buj-Corral I., Vivancos-Calvet J., Coba-Salcedo M. Modelling of surface finish and material removal rate in rough honing. Precision Engineering, 2014, vol. 38, no. 1, pp. 100–108. doi: 10.1016/j.precisioneng.2013.07.009.
  3. Barakaev N.R., Isamov R.N., Rakhmonov S.K. ugli. Improvement of quality of internal cylindrical surfaces. European Scholar Journal, 2021, vol. 2, no. 6, pp. 60–63.
  4. Pawlus P., Reizer R., Wieczorowski M. Analysis of surface texture of plateau-honed cylinder liner – A review. Precision Engineering, 2021, vol. 72, pp. 807–822. doi: 10.1016/j.precisioneng.2021.08.001.
  5. Zhang Xueping, Zhou Zaoyang, Yao Zhenqiang, Xi Lifeng. Analytically Predicating the Multi-Dimensional Accuracy of the Honed Engine Cylinder Bore. Journal of Tribology, 2020, vol. 142, no. 9, article number 091201. doi: 10.1115/1.4046677.
  6. Yang Changyong, Su Hao, Gao Shaowu, Fu Yucan, Ding Wenfeng, Xu Jiuhua. Surface quality and geometric accuracy control of fuel nozzle single-pass honing. The International Journal of Advanced Manufacturing Technology, 2021, vol. 114, pp. 3325–3336. doi: 10.1007/s00170-021-07103-5.
  7. Bobrovskiy I.N. The characterization parameters of the texture after honing. Bulletin of the South Ural State University. Series “Mechanical engineering industry”, 2017, vol. 17, no. 3, pp. 26–35. doi: 10.14529/engin170303.
  8. Hoffmeister H.-W., Grosse Т., Gerdes A. Investigation of the Influence of Different Process Setting Parameters on the Surface Formation at Honing of Thermally Sprayed Layers. Procedia CIRP, 2012, vol. 1, pp. 371–376. doi: 10.1016/j.procir.2012.04.066.
  9. Schmitt С., Bahre D. An Approach to the Calculation of Process Forces During the Precision Honing of Small Bores. Procedia CIRP, 2013, vol. 7, pp. 282–287. doi: 10.1016/j.procir.2013.05.048.
  10. Barylski A., Sender P. The Proposition of an Automated Honing Cell with Advanced Monitoring. Machines, 2020, vol. 8, no. 4, article number 70. doi: 10.3390/machines8040070.
  11. Schmitt C., Bahre D. Analysis of the Process Dynamics for the Precision Honing of Bores. Procedia CIRP, 2014, vol. 17, pp. 692–697. doi: 10.1016/j.procir.2014.01.055.
  12. Akkurt A. Comparison of Roller Burnishing Method with Other Hole Surface Finishing Processes Applied on AISI 304 Austenitic Stainless Steel. Journal of Materials Engineering and Performance, 2010, vol. 20, pp. 960–968. doi: 10.1007/s11665-010-9718-x.
  13. Pawlus P., Cieslak T., Mathia T. The study of cylinder liner plateau honing process. Journal of Materials Processing Technology, 2009, vol. 209, no. 20, pp. 6078–6086. doi: 10.1016/j.jmatprotec.2009.04.025.
  14. Sabri L., El Mansori M. Process variability in honing of cylinder liner with vitrified bonded diamond tools. Surface and Coatings Technology, 2009, vol. 204, no. 6-7, pp. 1046–1050. doi: 10.1016/j.surfcoat.2009.05.013.
  15. Kapoor J. Parametric Investigations into Bore Honing through Response Surface Methodology. Materials Science Forum, 2014, vol. 808, pp. 11–18. doi: 10.4028/ href='www.scientific.net/MSF.808.11' target='_blank'>www.scientific.net/MSF.808.11.
  16. El Mansori M., Goeldel В., Sabri L. Performance impact of honing dynamics on surface finish of precoated cylinder bores. Surface and Coatings Technology, 2013, vol. 215, pp. 334–339. doi: 10.1016/j.surfcoat.2012.09.062.
  17. Babichev A.P., Polyanchikov Yu.N., Slavin A.V., Shumyacher V.M., Polyanchikova M.Yu., Gusakova L.V. Khoningovanie [Honing]. Volgograd, VolgGASU Publ., 2013. 246 p.
  18. Kremen Z.I., Stratievskiy I.Kh. Khoningovanie i superfinishirovanie detaley [Honing and superfinishing of parts]. Leningrad, Mashinostroenie Publ., 1988. 137 p.
  19. Buyukli I.M., Kolesnik V.M. Improving accuracy of holes honing. Trudy Odesskogo politekhnicheskogo universiteta, 2015, no. 1, pp. 34–43. EDN: TSNFFJ.
  20. Naerman M.S., Popov S.A. Pretsizionnaya obrabotka detaley almaznymi i abrazivnymi bruskami [Precision machining of parts with diamond and abrasive stones]. Moscow, Mashinostroenie Publ., 1971. 224 p.

Supplementary files

Supplementary Files
Action
1. JATS XML
Download

Copyright (c) 2024 Denisenko A.F., Grishin R.G., Antipova E.D.

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

This website uses cookies

You consent to our cookies if you continue to use our website.

About Cookies