Irregularity of microhardness and microstructure of low-carbon steel rolled in a two-stand rolling-leveling mill

Cover Page

Cite item

Full Text

Abstract

The relevance of the study is proved by two factors. One of them is the necessity to study the nature of the change in the microstructure of the cross-section of extra-thin tinplate made of TS 435 steel (analogue of 08ps steel) skin-passed in a new DSR-1250 mill of the Miory Metal Rolling Plant. The second factor is the need to develop an effective method for obtaining accurate geometry characteristics of an oblique cut of tinplate 0.19 mm or less thick. The purpose of the work is to determine the changes in microhardness and microstructure over the thickness of tinplate samples and identify the existence of a layer microstructure necessary for this type of flat-rolled products. The study was carried out on the selected samples of tinplate of TS 435 steel 0.19 mm thick. This tinplate was rolled from an annealed strip, 0.224 mm thick. The total magnitude of reduction in the mill was 15 %, and the reduction in the skin-pass stand was at least 3 %. The authors carried out measurements of microhardness at different points over the thickness of the selected tinplate samples. The microhardness values over the strip thickness were averaged using 6th degree polynomial interpolation. To study the grain dimension, a number of microstructure images were taken in various areas over the sheet thickness with ×500 magnification. The microstructure studies showed a pronounced strain microstructure with grains elongated in the direction of rolling. At the very boundary of metal contacting the rolls, the grains received the greatest deformation. The highest values of microhardness were identified in two zones adjacent to both strip surfaces and in the central layers along the strip thickness. The change in the microhardness values along the sheet thickness has a wave-like character with three pronounced zones of increase in hardness and two zones of a decrease in its values. The zones with the lowest microhardness values are located between the zones with the maximum values.

About the authors

Vladimir P. Ivanov

Euphrosyne Polotskaya State University of Polotsk, Novopolotsk

Email: v.ivanov@psu.by
ORCID iD: 0000-0002-4621-7155

Doctor of Sciences (Engineering), Professor

Белоруссия

Stanislav V. Pilipenko

Euphrosyne Polotskaya State University of Polotsk, Novopolotsk

Author for correspondence.
Email: 44-08@mail.ru
ORCID iD: 0000-0002-1110-2016

PhD (Engineering), Associate Professor

Белоруссия

Oleg P. Shtempel

Euphrosyne Polotskaya State University of Polotsk, Novopolotsk

Email: o.shtempel@psu.by
ORCID iD: 0000-0001-7247-0798

PhD (Engineering), Associate Professor

Белоруссия

Tatyana V. Vigerina

Euphrosyne Polotskaya State University of Polotsk, Novopolotsk

Email: t.vigerina@psu.by
ORCID iD: 0000-0002-8862-5456

PhD (Engineering), Associate Professor

Белоруссия

References

  1. Mazur V.L., Nogovitsyn O.V. Theory and Technology of Sheet Rolling: Numerical Analysis and Applications. London, CRS Press Publ., 2019. 477 p.
  2. Mazur V.L. Preventing surface defects in the uncoiling of thin steel sheet. Steel in Translation, 2015, no. 45, pp. 959–966. doi: 10.3103/S0967091215120062.
  3. Wang D.-С., Liu H.-M., Liu J. Research and Development Trend of Shape Control for Cold Rolling Strip. Chinese Journal of Mechanical Engineering, 2017, no. 30, pp. 1248–1261. doi: 10.1007/s10033-017-0163-8.
  4. Kozhevnikov А.V. The Development and Application of Methodologies for the Design of Technological Modes of Cold Rolling. IOP Conference Series: Materials Science and Engineering, 2020, vol. 718, article number 012007. doi: 10.1088/1757-899X/718/1/012007.
  5. Pimenov A.F., Soskovets O.N., Trayno A.I., Mazur V.L., Chernov P.P., Dobronravov A.I. Kholodnaya prokatka i otdelka zhesti [Cold rolling and finishing of tinplate]. Moscow, Metallurgiya Publ., 1990. 206 p.
  6. Timofeeva M.A., Garber E.A. Protsess dressirovki kholodnokatanykh stalnykh polos (teoriya, tekhnologiya, oborudovanie, tendentsii ikh razvitiya i sovershenstvovaniya) [The process of training cold-rolled steel strips (theory, technology, equipment, trends in their development and improvement)]. Cherepovets, ChGU Publ., 2017. 155 p.
  7. Ogarkov N.N., Zvyagina E.Y., Ismagilov R.R. Theoretical analysis of formation of automobile sheet roughness during temper rolling in shot-blasted rolls. Steel in Translation, 2019, vol. 49, no. 8, pp. 499–503. doi: 10.3103/S0967091219080138.
  8. Cui H., Chen H., Lu L., He Z. Determinant parameters of surface morphology to corrosion behaviour of cold-rolled auto sheet steel. Journal of Materials Science, 2021, no. 56, pp. 8297–8308. doi: 10.10078/s10853-021-05812-6.
  9. Poddar V.S., Rathod M.J. Evaluation of mechanical properties of cold roll bonded mild steel and aluminum. Materials Today: Proceedings, 2021, vol. 43-5, pp. 3014–3022. doi: 10.1016/j.matpr.2021.01.363.
  10. Li T., Yan S., Liu X. Enhancement austenite content in medium-Mn steel by introducing cold-rolled deformation and inhibiting subsequent recrystallization. Materials Letters, 2021, vol. 301, article number 130249. doi: 10.1016/j.matlet.2021.130249.
  11. Mazur V.L., Nogovitsyn O.V. Theory and Technology of Sheet Rolling. Numerical Analysis and Applications. New York, CRC Press Publ., 2018. 500 p.
  12. Zakarlyuka S.V., Yurchenko Yu.I., Goncharov V.E., Budakva S.A. Non-flatness parameters variation in case of elastic stretching of strips Non-flatness parameters variation in case of elastic stretching of strips. Modelirovanie i razvitie protsessov OMD, 2018, no. 24, pp. 3–12. EDN: UQLSOA.
  13. Zaytsev A.I., Rodionova I.G., Koldaev A.V., Arutyunyan N.A., Aleksandrova N.M. Effect of composition and processing parameters on microstructure and mechanical properties of cold-rolled and galvanized roll products from IF-steels. Metallurg, 2020, no. 6, pp. 41–47. EDN: URLJOH.
  14. Dyakonov V.A., Pilipenko S.V., Shtempel O.P. Influence of deformation on the mechanical properties of tin-plated tin. Vestnik Polotskogo gosudarstvennogo universiteta. Seriya B. Promyshlennost. Prikladnye nauki, 2022, no. 10, pp. 18–24. EDN: YFNRXI.
  15. Li L., Matsumoto R., Utsunomiya H. Experimental Study of Roll Flattening in Cold Rolling Process. ISIJ International, 2018, vol. 58, no. 4, pp. 714–720. doi: 10.2355/isijinternational.ISIJINT-2017-623.
  16. Bogush R.P., Adamovskiy E.R., Denisenok S.F. Processing and analysis of images of microstructure metals for determining the grain point. Doklady Belorusskogo gosudarstvennogo universiteta informatiki i radioelektroniki, 2021, vol. 19, no. 4, pp. 70–79. doi: 10.35596/1729-7648-2012-19-4-70-79.
  17. Anisovich A.G. Problems of application of standards in evaluation of microstructure of metals and alloys. Izvestiya Natsionalnoy akademii nauk Belarusi. Seriya Fiziko-tekhnicheskikh nauk, 2021, vol. 66, no. 1, pp. 12–19. doi: 10.29235/1561-8358-2021-66-1-12-19.
  18. Anisovich A.G., Rumyantseva I.N., Bislyuk L.V. Determination of steel grain grade by computer methods. Lite i metallurgiya, 2010, no. 3S, pp. 100–104. EDN: UINMCT.
  19. Anisovich A.G., Andrushevich A.A. Mikrostruktury chernykh i tsvetnykh metallov [Microstructures of ferrous and non-ferrous metals]. Minsk, Belaruskaya navuka Publ., 2015. 131 p.
  20. Li S., Wang Z., Guo Y. A novel analytical model for prediction of rolling force in hot strip rolling based on tangent velocity field and MY criterion. Journal of Manufacturing Processes, 2019, vol. 47, pp. 202–210. doi: 10.1016/j.jmapro.2019.09.037.

Supplementary files

Supplementary Files
Action
1. JATS XML
Download

Copyright (c)



This website uses cookies

You consent to our cookies if you continue to use our website.

About Cookies