THE INFLUENCE OF HEATING TEMPERATURE FOR FORGING ON THE CRACKING TENDENCY OF A Cu-Mn-Al-Fe-Ni 59-3.5-2.5-0.5-0.4 WORKPIECE


Cite item

Full Text

Abstract

Since the cause of the delayed destruction of the two-phase brasses is not fully determined, the commercial supplies of semi-finished products have unstable technological properties. As the result of experimental work, the author obtained the contradictory data on the root cause of cracking and the influence of grain growth during heating on the crack formation tendency. Meanwhile, the current requirements to the technological processes need the maximum loss minimization during the mill products processing.
The paper covers the issue of the selection of temperature intervals of hot plastic deformation to eliminate and determine the relationship between the β-phase grain size and the cracking carried out on the basis of industrial experiment followed by the comparative metallographic analysis of batches with different handling properties. For this purpose, the author carried out the comparative industrial experiment between the batches with different handling properties, determined the actual temperature of hot deformation, and performed the controlled forging at different heating temperatures. The subsequent metallographic analysis proved the assumption that the increase in the forging temperature can increase the level of deviations in some cases and reduce in the others. The author studied the influence of the initial microstructure of the CuMnAlFeNi 59-3.5-2.5-0.5-0.4 alloy, the heating temperature of forging by the level and the type of defects of work material for the blocking synchronizer rings made of different batches of tubes. It is determined that the conditions for the production of pipes are the more significant factor for cracking than the heating temperature at the certain interval. When heating up to 780 °C, the large grains are formed in the individual batches that may be caused by the initial β'-phase grain texture but is not the root cause of destruction. When heating up to 700 °C, the high dispersion silicides do not dissolve, what may cause the origination of hidden cracks during forging. The optimum heating temperature is 750 °C.

About the authors

A. V. Svyatkin

Togliatti State University

Author for correspondence.
Email: Aleksey.Svyatkin@vaz.ru

Svyatkin Aleksey Vladimirovich - PhD (Engineering), Associate Professor.
445020, Togliatti, Belorusskaya Street, 14. Tel.: (8482) 53-46-32

Россия

References

  1. Bobylev A.V. Rastreskivanie mednykh splavov [Cracking of copper alloys]. Moscow, Metallurgiya Publ., 1993. 352 p.
  2. Kurbatkin I.I., Belov N.A., Raykov Yu.N., Gorin A.D., Antipov V.V. Formation of the structure of multicomponent manganese brass and its relationship with the appearance of marriage. Izvestiya vysshikh uchebnykh zavedeniy. Tsvetnaya metallurgiya, 2002, no. 5, pp. 58-62.
  3. Tropotov A.B., Zhukova L.M., Ryazantsev Yu.V., Kopyl M.D., Kotlyarov I.V. Optimization of the chemical composition and properties of the special brass for the manufacture of blocking rings of synchronizers of a transmission. Materialy v avtomobilestroenii: materialy II Mezhdunarodnoy nauchno-prakticheskoy konferentsii. Tolyatti, AVTOVAZ Publ., 2004, pp. 389-394.
  4. Tropotov A.V., Pugacheva N.B., Ryazantsev Yu.V., Zhukova L.M. A study of residual stresses in articles produced from complexly-alloyed brass. Metal Science and Heat Treatment, 2006, vol. 48, no. 1-2, pp. 31-35.
  5. Ovchinnikov A.S., Loginov Yu.N. Development of technology for manufacture of Cu-Zn-Mn-Al-Fe-Ni brass tubes. Zagotovitelnye proizvodstva v mashino-stroenii, 2014, no. 11, pp. 24-28.
  6. Pugacheva N.B. Structure of industrial а+в brasses. Metal Science and Heat Treatment, 2007, vol. 49, no. 1-2, pp. 67-74.
  7. Pugacheva N.B., Tropotov A.V., Smirnov S.V., Kuzmin O.S. Effect of iron content on the composition and morphology of (Fe,Mn)5Si3 silicide particles in alloyed LMTssaZhKS brass. The physics of metals and metallography, 2000, vol. 89, no. 1, pp. 62-69.
  8. Pugacheva N.B., Lebed A.V. The influence of the pressed hollow billet of brass 59Cu-3,5Mn-2,5Al-0,5Fe-0,4Ni structure on the fracture mode of destruction with following hot stamping. Vestnik Samarskogo gosudar-stvennogo tekhnicheskogo universiteta. Seriya: Fiziko-matematicheskie nauki, 2012, no. 4, pp. 180-187.
  9. Kopyl V.D., Azizbekyan V.G. Reasearh of the reasons cracks formation in the production course of the blocking rings of synchronizers from complex alloy brass Cu-Mn-Al-Fe-Ni on the Volga automobile works. Deformatsiya i razrushenie materialov i nanoma-terialov: sbornik trudov III Mezhdunarodnoy konferentsii. Moscow, FGBUN IMiM im. A.A. Baykova Publ., 2009, pp. 360-362.
  10. Kolachev B.A., Elagin V.I., Livanov V.A. Metallovedenie i termicheskaya obrabotka metallov i splavov [Physical Metallurgy and Heat Treatment of Nonferrous Metals and Alloys]. Moscow, MISIS Publ., 2001. 416 p.
  11. Kotov D.A., Mysik R.K., Eremin A.A., Volkov M.I., Zhukova L.M. Prediction of the phase composition of complex alloyed brass. Liteyshchik Rossii, 2005, no. 9, pp. 17-21.
  12. Svyatkin A.V. Obespechenie stabilnosti fazovogo sostava i svoystv iznosostoykikh latuney tipa LMtsA dlya izgotovleniya detaley avtomobilnogo naznacheniya. Dis. kand. tekhn. nauk [Ensuring stability of phase composition and properties of wear-resistant brasses of Face type for the manufacture of automotive parts]. Samara, 2009. 165 p.
  13. Muratov V.S., Svyatkin A.V. Perfection of manufacturing technology of LMTsA brass bars. Zagotovitelnye proizvodstva v mashinostroenii, 2007, no. 2, pp. 36-39.
  14. Shenderey P.E., Svyatkin M.V., Svyatkin A.V., Lazu-tov P.N. Prasolov S.G. Determination of the practical applicability of predicting the phase composition of complex alloyed brass. Evraziyskoe nauchnoe obedinenie, 2015, vol. 1, no. 7, pp. 35-37.
  15. Sokolov I.A., Uralskiy V.I. Ostatochnye napryazheniya i kachestvo produktsii [Residual stresses and product quality]. Moscow, Metallurgiya Publ., 1981. 96 p.
  16. Osintsev O.E., Fedorov V.N. Med i mednye splavy. Otechestvennye i zarubezhnye marki [Copper and copper alloys. Domestic and foreign brands]. Moscow, Mashinostroenie Publ., 2004. 336 p.
  17. Kurbatkin I.I., Belov N.A., Raykov Yu.N., Rumyantseva O.V., Pokhlebenina L.A., Antipov V.V. Effect of alloying elements and technological factors on phase composition and properties of brass tubes used in the automotive industry. Tsvetnye metally, 2001, no. 5, pp. 73-76.
  18. Svyatkin A.V., Muratov V.S. Research of dependence of phase structure and hardness from annealing temperature LMtsA58-2-1 two-phase brass. Zagotovitelnye proizvodstva v mashinostroenii, 2009, no. 10, pp. 37-39.
  19. Kurbatkin I.I., Pruzhinin I.F., Falkon V.I., Kurbatov V.P. Effect of chemical compound and treatment schedule on the mechanical and operational properties of siliconmanganese brasses. Tsvetnye metally, 1996, no. 9, pp. 60-63.
  20. Drits M.E., Bochvar N.R., Guzey L.S., Lysova E.V. Dvoynye i mnogokomponentnye sistemy na osnove medi [Double and multicomponent systems on the basis of copper]. Moscow, Nauka Publ., 1979. 375 p.
  21. Lyakisheva N.P., ed. Diagrammy sostoyaniya dvoynykh metallicheskikh system [Charts of a condition of double metal systems]. Moscow, Mashinostroenie Publ., 1997. Vol. 3, kn. II, 1024 p.

Supplementary files

Supplementary Files
Action
1. JATS XML
Download

Copyright (c)



This website uses cookies

You consent to our cookies if you continue to use our website.

About Cookies